Lasers

LASER stands for light amplification by stimulated emission of radiation.
A laser is an electronic-optical device that emits coherent light radiation. The term "laser" is an acronym for Light Amplification by Stimulated Emission of Radiation. A typical laser emits light in a narrow, low-divergence beam, with a narrow wavelength spectrum ("monochromatic" light). In this respect, laser light is in sharp contrast with such light sources as the incandescent light bulb, which emits incoherent light (out of phase with itself) over a wide area and over a wide spectrum of wavelengths, and differs from LED light which is not coherent.
The first working laser was demonstrated on May 16, 1960 by Theodore Maiman at Hughes Research Laboratories. Since then, lasers have become a multi-billion dollar industry. The most widespread citation needed use of lasers is in optical storage devices such as compact disc and DVD players, in which the laser (a few millimeters in size) scans the surface of the disc. Other common applications of lasers are bar code readers, laser printers and laser pointers.
In industry, lasers are used for cutting steel and other metals and for inscribing patterns (such as the letters on computer keyboards). Lasers are also commonly used in various fields in science, especially spectroscopy, typically because of their well-defined wavelength or short pulse duration in the case of pulsed lasers. Lasers are used by the military for rangefinding, target identification and illumination for weapons delivery. Lasers have also recently begun to be used as weapons. Lasers used in medicine are used for internal surgery and cosmetic applications.

Design of laser:
A laser consists of a gain medium inside a highly reflective optical cavity, as well as a means to supply energy to the gain medium. The gain medium is a material with properties that allow it to amplify light by stimulated emission. In its simplest form, a cavity consists of two mirrors arranged such that light bounces back and forth, each time passing through the gain medium. Typically one of the two mirrors, the output coupler, is partially transparent. The output laser beam is emitted through this mirror.Light of a specific wavelength that passes through the gain medium is amplified (increases in power); the surrounding mirrors ensure that most of the light makes many passes through the gain medium, being amplified repeatedly. Part of the light that is between the mirrors (that is, within the cavity) passes through the partially transparent mirror and escapes as a beam of light.
The process of supplying the energy required for the amplification is called pumping. The energy is typically supplied as an electrical current or as light at a different wavelength. Such light may be provided by a flash lamp or perhaps another laser. Most practical lasers contain additional elements that affect properties such as the wavelength of the emitted light and the shape of the beam.

Modes of operation
The output of a laser may be a continuous constant-amplitude output (known as CW or continuous wave); or pulsed, by using the techniques of Q-switching, modelocking, or gain-switching. In pulsed operation, much higher peak powers can be achieved.
Some types of lasers, such as dye lasers and vibronic solid-state lasers can produce light over a broad range of wavelengths; this property makes them suitable for generating extremely short pulses of light, on the order of a few femtoseconds (10-15 s).

Continuous wave operation
In the continuous wave (CW) mode of operation, the output of a laser is relatively consistent with respect to time. The population inversion required for lasing is continually maintained by a steady pump source.

Pulsed operation
In the pulsed mode of operation, the output of a laser varies with respect to time, typically taking the form of alternating 'on' and 'off' periods. In many applications one aims to deposit as much energy as possible at a given place in as short time as possible. In laser ablation for example, a small volume of material at the surface of a work piece might evaporate if it gets the energy required to heat it up far enough in very short time. If, however, the same energy is spread over a longer time, the heat may have time to disperse into the bulk of the piece, and less material evaporates. There are a number of methods to achieve this.

Q-switching
In a Q-switched laser, the population inversion (usually produced in the same way as CW operation) is allowed to build up by making the cavity conditions (the 'Q') unfavorable for lasing. Then, when the pump energy stored in the laser medium is at the desired level, the 'Q' is adjusted (electro- or acousto-optically) to favorable conditions, releasing the pulse. This results in high peak powers as the average power of the laser (were it running in CW mode) is packed into a shorter time frame.

Modelocking
A modelocked laser emits extremely short pulses on the order of tens of picoseconds down to less than 10 femtoseconds. These pulses are typically separated by the time that a pulse takes to complete one round trip in the resonator cavity. Due to the Fourier limit (also known as energy-time uncertainty), a pulse of such short temporal length has a spectrum which contains a wide range of wavelengths. Because of this, the laser medium must have a broad enough gain profile to amplify them all. An example of a suitable material is titanium-doped, artificially grown sapphire (Ti:sapphire).
The modelocked laser is a most versatile tool for researching processes happening at extremely fast time scales also known as femtosecond physics, femtosecond chemistry and ultrafast science, for maximizing the effect of nonlinearity in optical materials (e.g. in second-harmonic generation, parametric down-conversion, optical parametric oscillators and the like), and in ablation applications. Again, because of the short timescales involved, these lasers can achieve extremely high powers.

Pulsed pumping
Another method of achieving pulsed laser operation is to pump the laser material with a source that is itself pulsed, either through electronic charging in the case of flashlamps, or another laser which is already pulsed. Pulsed pumping was historically used with dye lasers where the inverted population lifetime of a dye molecule was so short that a high energy, fast pump was needed. The way to overcome this problem was to charge up large capacitors which are then switched to discharge through flashlamps, producing a broad spectrum pump flash. Pulsed pumping is also required for lasers which disrupt the gain medium so much during the laser process that lasing has to cease for a short period. These lasers, such as the excimer laser and the copper vapour laser, can never be operated in CW mode.

Uses of lasers:
When lasers were invented in 1960, they were called "a solution looking for a problem". Since then, they have become ubiquitous, finding utility in thousands of highly varied applications in every section of modern society, including consumer electronics, information technology, science, medicine, industry, law enforcement, entertainment, and the military.
The first application of lasers visible in the daily lives of the general population was the supermarket barcode scanner, introduced in 1974. The laserdisc player, introduced in 1978, was the first successful consumer product to include a laser, but the compact disc player was the first laser-equipped device to become truly common in consumers' homes, beginning in 1982, followed shortly by laser printers.
Some of the other applications include:
Medicine: Bloodless surgery, laser healing, surgical treatment, kidney stone treatment, eye treatment, dentistry
Industry: Cutting, welding, material heat treatment, marking parts
Defense: Marking targets, guiding munitions, missile defence, electro-optical countermeasures (EOCM), alternative to radar
Research: Spectroscopy, laser ablation, Laser annealing, laser scattering, laser interferometry, LIDAR
Product development/commercial: laser printers, CDs, barcode scanners, thermometers, laser pointers, holograms, bubblegrams.
Laser skin procedures such as acne treatment, cellulite reduction, and hair removal.